• Maintenance Primer

    Article No. 150401

    Maintenance Primer

    Special primer for lightening weathered and greyed woods

    Colour: spruce | 1504
    Size / Quantity

    Discontinued product This container size is being phased out and is only available to a limited extent.

    Product specifications

    On delivery

    Binder Acrylate/alkyd system
    Density (20°C) 1.07 g/cm³
    Odour Mild

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for dimensionally stable elements
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For use on interior and exterior wood
    • Dimensionally stable wood building elements: e.g. windows and doors
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
    • Maintenance and levelling of greyed and spotted wood surfaces

    Properties

    • Water-based
    • Weatherproof and moisture-regulating
    • Quick drying
    • Good coverage with just one coat
    • Very good adhesion to the substrate
    • Preparation
      • Substrate requirements

        Dimensionally stable wood building elements: wood moisture content 11-15%

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Using a brass brush, thoroughly clean greyed and weathered wood surfaces to ensure optimum adhesion.

        Remove loose and torn knots as well as resin that bleeds and clean with a suitable product (e.g. Remmers thinner & brush cleaner).

        Exterior wood that needs to be protected against soft rot and blue stain must be pre-treated with a suitable wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Round off sharp edges.

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

    • Application
      • Stir before use
      • Brush
      • Application requirements

        Temperature of the material, air and substrate: from min. +5 °C to max. +30 °C

      • Stir well.

        Apply by brush.

        Apply in the direction of the grain.

        After drying, apply the intermediate and final coats of LT Stain UV.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Before coating technically modified woods and wood-based materials, apply the coating to a trial surface and conduct a suitability test on the desired area of use.

        When renovating windows and exterior doors, we recommend an intermediate sanding step using sandpaper (P180) or a fine sanding sponge prior to further coating.

      • Drying

        Can be overcoated: after approx. 4 hours

        Practice values at +20 °C and 65% relative humidity.

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        Ready for use

    • Working tools / cleaning
      • Brush
      • Acrylic brush, flat brush

      • Clean tools immediately after use with water and detergent.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 24 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.

        Use the contents of open containers as quickly as possible.

    • Usage
      • Total application/absorption rate 100 ml Total / m²
      • Approx. 100 ml/m² depending on the absorbency of the wood.

    • General information
      • Observe the regulations concerning design principles for wood protection.

        Do not use on horizontal surfaces without drainage slopes and without edge radius, avoid accumulated moisture.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.