Article No. 328005

    Induline GW-343

    Water-based, translucent special primer for wooden doors

    Colour: special colours | 3280
    Size / Quantity



    Product specifications

    On delivery

    Binder special resins
    Density (20°C) 1.020 - 1.100 g/cm³ depending on the colour
    Odour characteristic

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for exterior doors
    • For professional users only
    • For use on interior and exterior wood
    • Soft and hard woods
    • Dimensionally stable wood building elements: front doors
    • Not suitable for wooden windows


    • Water-based
    • Long open time for streak-free application (on large surfaces)
    • Good pore wetting performance
    • Outstanding (wet) adhesion
    • Film preserver protects against microbial damage
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Dimensionally stable wood building elements: wood moisture content 11-15%

      • Preparations

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Sand the substrate, remove dust and pre-treat with levelling primer VP21567 if necessary.

    • Application
      • Temperature of the material, air and substrate: from min. +15 °C to max. +30 °C
      • Stir before use
      • By brush / Spraying in closed palnts
      • Application requirements

        Temperature of the material, air and substrate: +15 °C to +30 °C. Relative humidity 40 - 80%

      • Stir well, including during application or after a break in work.

        Use airless spraying equipment to spray onto the front door at low pressure, then spread evenly with a paintbrush.

        Apply 1-2 coats as necessary with light sanding in between.

        Once dry, apply further coatings.

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 3-4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Substances in oak may bleed, causing dark discolouration, when coated with water dilutable dispersion stains.

        Apply forced drying to tannin-containing woods.

        The best flow results on Accoya, oak and chestnut are achieved at a pH value of 9.0–9.5, corresponding to an additive content of 0.3–0.5% VP 20829 Additive (0366).

        Divide large surfaces into strips and do not coat extensive areas all at once.

      • Drying

        Overcoating: after approx. 3-4 hours (at 23 °C and 50% RH) If forced drying is used, ready for overcoating: after approx. 90 minutes (20 minutes dripping/50 minutes drying phase (35 – 40 °C)/20 minutes cooling phase)

    • Working tools / cleaning
      • By brush / Spraying in closed palnts
      • Paintbrush, spraying equipment

      • Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 100 ml - 150 ml / m² per layer applied
      • 100 – 150 ml/m² per coat

      • Depending on the processing method, wood type and wood surface.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.