Article No. 268220
Solvent-based, translucent intermediate and finishing coat for spray application
Downloads & documents
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- For use on interior and exterior wood
- Soft and hard woods
- Dimensionally stable wood building elements: e.g. windows and doors
- Intermediate and finishing coats
- Finishing coat on inner sides of windows exposed to high moisture levels (e.g. swimming pools)
- Particularly cost-effective thanks to high solid content
- Good flow properties
- Weatherproof and moisture-regulating
- High level of UV resistance and colour stability
- Special combination of binding agents creates an extremely hard-wearing surface
The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.
Dimensionally stable wood building elements: wood moisture content 11-15%
If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).
Pre-treat using a suitable primer & intermediate coat and carry out intermediate sanding if necessary.
Temperature of the material, air and substrate: from min. +5 °C to max. +30 °C.
Airless spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar.
Air-mix spraying: nozzle size: 0.28-0.33 mm; material pressure: 70-90 bar, atomiser air pressure 1-2 bar.
Seal opened containers well and use contents as soon as possible.
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
Ensure good ventilation.
The clear colour version of the product is not suited for use on exterior surfaces that are directly exposed to weather.
The product should not be applied at the same work stand as NC-based varnishes or stains. Collect any textiles soiled with the product (e.g. cleaning rags, work clothing) in fire-resistant waste containers and dispose of properly.
Collect contaminated filter mats in a fire-resistant waste container and dispose of properly.
Leave fresh spraying dust to dry before sweeping up.
Risk of self-ignition (DGUV information brochure 209-046).
When sanding wooden surfaces that have been treated with the product, always wear respiratory protection (dust filter mask P2).
On surfaces that are not exposed to daylight, e.g. the inner surfaces of windows and external doors, alkyd resin systems exhibit a certain degree of dark yellowing, in particular in rebates.
Touch-dry: after approx. 8 hours Ready for overcoating: after approx. 12 hours
Practice values at +20 °C and 65% relative humidity.
Drying may be significantly delayed at lower temperatures, high humidity, in poor air circulation or if the maximum layer thickness is exceeded.
Ready to use
Working tools / cleaning
Hand spray guns, automatic spraying equipment
Clean tools immediately after use with V 101 Thinner. Dispose of the remains from cleaning properly.
Storage / shelf life
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 24 months.
Approx. 125 ml/m² (plus spray loss) per coat (corresponds to wet film thickness: approx. 125 µm, dry film thickness: approx. 50 µm)
The final degree of gloss only sets in approx. 2-3 weeks after application. There may be slight differences in the gloss level depending on the colour.
Sealing compounds must be compatible with the coating and may only be applied once the coating has dried thoroughly.
Care and maintenance:
Wood is subjected to great climatic and environmental stresses when outdoors. The coat is susceptible to the processes of natural ageing, wear and decomposition. Decomposition takes place at different speeds, depending on the stress (weak, average, strong) placed on the wood building element. Weathering stages may vary according to the part or element affected. To give wood the longest and best possible protection it is advisable to examine surfaces every year. Any damage found should be addressed immediately after cleaning.
For cleaning and care, we recommend the care set for windows (2745) and doors (2746).
Apply a top-up coat of HSL-30 and MSL-40
Observe current standards and guidelines for coating wood building elements outdoors (Codes of Practice issued by the German Association of Window and Facade Manufacturers (VFF), Code of Practice No. 18 issued by the German Federal Committee for Paint and the Protection of Material Assets (BFS), guidelines issued by the German Lacquer and Printing Ink Association (VdL) and ift guidelines issued by the Institut für Fenstertechnik).
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
Safety / regulations
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.