Article No. 398720

    Induline LW-710

    Water-based low-build stain for interior and exterior wood

    Colour: clear | 3987
    Colour: clear | 3987
    Please choose a colour
    Size / Quantity

    Product specifications

    On delivery

    Binder Acrylate/alkyd system
    Density (20°C) Approx. 1.04 g/cm³
    Odour Characteristic
    Degree of gloss Glossy

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors and outdoors
    • for elements with limited dimensional stability
    • for not dimensionally stable elements
    • For professional users only
    • For use on interior and exterior wood
    • Soft and hard woods
    • Wood building elements with limited dimensional stability, e.g. folding shutters, matchboarding, summerhouses
    • Wood building elements with no dimensional stability: e.g. fences, framework, carports, planking
    • Primer, intermediate and finishing coats

    Properties

    • Water-based
    • Water-based: does not give off any unpleasant odours and tools can be cleaned with water
    • Good flow properties
    • Quick drying: 2 coats can be applied in one day
    • Breathable
    • Outstanding (wet) adhesion
    • Special combination of binding agents creates an extremely hard-wearing surface
    • Does not flake
    • Free from film preservation and wood protection biocides
    • Preparation
      • Substrate requirements

        The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.

        Wood building elements with limited or no dimensional stability: wood moisture content max. 18%

      • Preparations

        Thoroughly remove any dirt, grease and non-adhering old coatings.

        Sand grey and weathered wood surfaces down to sound, bright wood.

        Thoroughly sand any old coatings that are still intact.

        If necessary, impregnate non-resistant woods with a wood preservative* (*Use biocides safely. Always read the label and product information before use).

        Observe BFS Code of Practice No. 18 "Coatings on Wood and Wooden Working Materials in Outdoor Areas".

        Remove any loose and torn knots as well as resin that bleeds from the wood and clean with a suitable product (e.g. V 101 Thinner, a nitrocellulose or universal thinner).

    • Application
      • Temperature of the material, air and substrate: from min. +15 °C to max. +25 °C
      • Stir before use
      • By brush / By roller Airless/airmix spraying / Flow cup gun
      • Application requirements

        Temperature of the material, air and substrate: from min. +15 °C to max. +25 °C.

      • Stir well, including during application or after a break in work.

        Apply with a brush, roller or by spraying.

        Airless spraying: nozzle size: 0.28 mm, material pressure: 80 - 120 bar.

        Airmix spraying: nozzle size: 0.28 mm, material pressure: 60-100 bar,
        atomiser air pressure: 1.2-2.0 bar.

        Flow cup gun: nozzle size: 1.8-2.0 mm, atomiser air pressure: 2-2.5 bar

        Seal opened containers well and use contents as soon as possible.

    • Application instructions
      • Drying time: can be worked over after 4 h
      • Check colour, adhesion and compatibility with the substrate by setting up a trial area.

        Ensure good ventilation.

      • Drying

        Low temperatures, poor ventilation and high humidity delay drying.

      • Thinning

        If necessary with water (max. 5%).

    • Working tools / cleaning
      • By brush / By roller Airless/airmix spraying / Flow cup gun
      • Airless/airmix spraying equipment, flow cup gun, acrylic brush, microfibre paint roller

        Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.

        Ensure that any residue from cleaning is disposed of correctly.

    • Storage / shelf life
      • Store frost-free and cool / protect for moisture / close containers
      • Shelf-life 12 months
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Approx. 100 ml - 150 ml / m² per layer applied
      • 100 - 150 ml/m² per coat in at least 2 coats

    • General information
      • DIN EN 71-3 "Migration of certain elements":

        This product complies with the limits for the migration of heavy metals to children's toys according to DIN EN 71-3 and thus fulfils one of several further requirements for the safety of children's toys according to the EU "Toy Directive" (2009/48/EC).

        On planed larch and softwoods with a high resin content, the coating may have reduced adhesion and resistance to weathering. This is especially the case on horizontal year rings, knots and areas of winter growth that are high in resin. Maintenance and renovation must be carried out more frequently on these surfaces.
        The only remedy for this is pre-weathering or very coarse sanding (P80).
        If these wood types are rough-sawn, considerably longer maintenance and renovation intervals are to be expected.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.