Article No. 266420
Water-based, opaque one-pot coating system for interior and exterior wood – reaction to fire tested according to DIN EN 13501-1
Product specifications
On delivery
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- Interior wood
- Exterior wood not directly exposed to weather
- Woods impregnated with Adolit BSS1
- Building elements with no or limited dimensional stability
- Roof structures
- Wall and ceiling panels
- Wall and ceiling constructions
- Shop fitting and trade fair stands
- Theatre and stage constructions
- Prefabricated timber houses
- Stables, sheds
Properties
- Approved for system use with Adolit BSS1
- Cloth matt
- Preservation of the wood structure
- Less discolouration due to water-soluble substances in the wood
- Quick drying: 2 coats can be applied in one day
- Water-based: does not give off any unpleasant odours and tools can be cleaned with water
-
Preparation
-
Substrate requirements
The substrate must be clean, dry, free of dust, grease and loose substances, and prepared in the correct manner.
Wood building elements with limited or no dimensional stability: wood moisture content max. 18%
-
Preparations
Use a brush to remove excess salt residues.
-
-
Application
-
Application requirements
Temperature of the material, air and substrate: +15 °C to +25 °C.
-
Stir well, including during application or after a break in work.
Application by brush, spraying
Flow cup gun: nozzle size: 2.0 - 2.5 mm; atomiser air pressure: 2.0 - 3.0 bar.
Airless spraying: nozzle size: 0.28 - 0.33 mm / 0.011 - 0.013 in, material pressure: 80 - 100 bar (use yellow pistol filter).
Airmix spraying: nozzle size: 0.28 - 0.33 mm / 0.011 - 0.013 in, material pressure: 70 - 90 bar, atomiser air pressure: 1 - 2 bar.
After drying and, if necessary, intermediate sanding (P 280 - 320), apply a second coat.
Seal opened containers well and use contents as soon as possible.
-
-
Application instructions
-
Check colour, adhesion and compatibility with the substrate by setting up a trial area.
The treated components must be protected against rain and moisture (enclosed spaces, covered structures etc.) and must not be exposed to weathering.
-
Drying
Can be overcoated: after approx. 4 hours
Practice values at +20 °C and 65% relative humidity.
Low temperatures, poor ventilation and high humidity delay drying.
-
Thinning
Ready to use
-
-
Working tools / cleaning
-
Brush, spraying equipment, board coating machine
-
Clean tools with water or Aqua RK-898 Cleaning Concentrate immediately after use.
Ensure that any residue from cleaning is disposed of correctly.
-
-
Storage / shelf life
-
Store in well-sealed, original containers, out of the reach of children and in a dry, cool, well-ventilated room which is protected from direct sunlight and frost. No smoking is permitted in storage areas.
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.
-
-
Usage
-
78 ml/m² (100 g/m²) per coat in 2 coats
-
-
General information
-
Packing:
When packing multiple wood components together, use an intermediate layer of foamed PE film to separate them from one another. Do not pull the packing tape on the wood packets too tight.
Care and maintenance:
The coating system must always be kept in good condition. Any damage must be immediately reworked or repaired using this product.
Indirect weathering can lead to condensation, which can cause white efflorescence on the wood surface. This does not impair the effectiveness.
Please refer to the relevant test reports/certificates and the Technical Data Sheet for information on certified products and configurations.
-
-
Disposal instructions
-
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
-
-
Safety / regulations
-
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.
-
