PBD 1K : Single-component bituminous thick coating

Article No. 087010

PBD 1K

Single-component, solvent-free, polymer-modified bituminous thick coating with rubber granulate fillers

Product variants

Variant table

Downloads & documents

Technical Data Sheet

Safety Data Sheet

Declaration of performamce

Implementation report

Environmental product declaration Deutsche Bauchemie e.V

Show all documents for download / dispatch

Product specifications

On delivery

Base Polymer/bitumen emulsion with rubber granules

Density of ready-to-use mixture Approx. 1.02 kg/l

Compressive behaviour Constant dry film thickness

Time until thoroughly dry
(20 °C/70% relative humidity) Approx. 48 hours

Consistency Paste-like, thixotropic

Test at pressure load = 0.3 MN/m² > 80 %

Crack-bridging ≥ 2 mm

Cross-slit pressure test (DIN 15820) Compliant even without reinforcement layer

Dry residue Approx. 75 vol.%

The stated values represent typical product characteristics and are not to be construed as binding product specifications.

Product details Application Usage / application examples Notes

Field of application

Waterproofing of new and old buildings with ground contact
Water effect classes W1.1-E, W1.2-E, W2.1-E, W3-E and W4-E according to DIN 18533
Retrofit waterproofing of buildings according to WTA Code of Practice 4-6
Waterproofing of foundations and base points

Properties

Solvent-free
Water pressure tight
Highly resistant to pressure > 0.3 MN/m²
Highly flexible, elastic and crack-bridging
Radon-tight (verified through testing)

Preparation
Substrate requirements

Even-surfaced, mineral substrate.

Clean, dust-free and capable of supporting a load.

Prepare concrete substrates at wall/base transition areas by means of mechanical material removal.

Matt damp surfaces are permitted.

If necessary, provide damp proofing.

Preparations

Remove projecting seams and mortar remains.

Break off or slope corners and edges.

Smooth out inner corners using a suitable mineral mortar.

Close indentations > 5 mm using a suitable mineral material.

Prime absorbent mineral substrates with Kiesol MB. Prime non-absorbent mineral substrates with BIT Primer [basic] (1:10 in water).

If the substrate requires reinforcement (restoration), prime using Kiesol (1:1 with water).

Create a scratch coat using the product as a contact layer and in order to prevent blisters.
Application
Application requirements

Temperature of the material, air and substrate: from min. +5 °C to max. +35 °C.

Ready to use, straight from the container.

Remove any dried material adhering to the edge of the bucket.

Apply the product in two layers on the previously prepared substrate.

If a reinforcement fabric is required, embed into the first waterproofing layer.
Application instructions
In the case of liquid-applied waterproofing materials, direct sunlight and/or wind exposure can cause accelerated skin formation and accompanying blistering.

Do not apply any further sealing layers until the previous layer has hardened sufficiently.

Protect freshly coated surfaces from rain, direct sunlight, frost and condensation.

Protect dry sealant from mechanical damage and UV radiation.

Please contact Remmers Technical Service (phone +49 5432 83900) before applying with machine processing.
Working tools / cleaning
Ladle, smoothing trowel, finishing scraper, suitable spraying equipment

Clean tools immediately after use with water.

Remove dried-on material using V 101 Thinner (0978).
Storage / shelf life
If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

Usage
Approx. 1.4 kg/m²/mm dry film thickness See application rate table under Application Examples for details

Application examples

Water exposure classes (DIN 18533)	Exposure class (DIN 18195) withdrawn as of July 2017	Dry film thickness (mm)	Wet film thickness (mm)	Application quantity (kg/m²)	Yield 25 kg (m²)
W1-E Soil moisture and non-pressing water	Load case 4 Soil moisture and non-pressing water	≥ 3	approx. 4.1	approx. 4.0	approx. 6.3
W2.1-E Moderate exposure to pressing water (anchoring depth ≤ 3m)	Load case 6 Standing seepage water and pressing water	≥ 4	approx. 5.5	approx. 5.5	approx. 4.5
W3-E Non-pressing water on soil-covered ceiling	Load case 5 Non-pressing water on soil-covered ceiling	≥ 4	approx. 5.5	approx. 5.5	approx. 4.5
W4-E Splashing water at wall plinth and capillary water in and underneath walls in contact with the ground	Plinth waterproofing in wall positioning area	≥ 3	approx. 4.1	approx. 4.0	approx. 6.3

Film thickness margin according to DIN 18533

du = scratch coat, application rate approx. 0.8 kg/m² (depending on the substrate)
dv = - not necessary with finishing scraper
- without finishing scraper: application rate approx. 0.6 kg/m² (dmin = 4mm)

General information
Deviations from applicable regulations must be agreed separately.

The relevant test certificates must be observed when planning and carrying out work.

The special agreements as well as test certificates can be downloaded online at www.remmers.com.
Disposal instructions
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
Safety / regulations
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.