• PP Fill

    Article No. 026125

    PP Fill

    Surface filler and fine plaster in the Power Protect [eco] system

    Colour: antique white | 0261
    Size / Quantity



    Product specifications

    On delivery

    Aw value / water absorption coefficient 13.32 kg/(m²h0.5)
    Reaction to fire Class A1
    Maximum grain size 0.5 mm
    Layer thickness Max. 5 mm
    Bulk density Approx. 1.2 kg/dm³
    w80 0.017 m³/m³
    Water requirement Approx. 7.5-8.5 l/25 kg
    Water vapour permeability µ < 14
    wsat 0.52 m³/m³
    Thermal conductivity λ 0.48 W/(m•K)
    Compressive strength class CS II (1.5-5.0 N/mm²)

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use on walls indoors and ceilings
    • Interior use
    • Creating fine, closed plaster surfaces that are ready for painting
    • Surface quality grades Q1-Q3


    • Enables water vapour diffusion
    • Highly capillary active
    • Good adhesive power
    • Insusceptible to moisture
    • Total layer thickness approx. 5 mm
    • Preparation
      • Substrate requirements

        Clean, dust-free and capable of supporting a load.

    • Application
      • Application temperature: min. 5 °C max. 30 °C
      • Toothed trowel / toothed blade
      • Reinforcing layer

        Using a toothed trowel, apply the material in a coating thickness of 3 mm.

        Embed the fabric in the centre of the reinforcement layer while it is still wet.

        Ensure that fabric sheets overlap by at least 10 cm.


        Surface decoration

        Apply material to a thickness of approx. 2 mm over the reinforcement layer once it has set sufficiently.

        Smooth the surface using a suitable tool.

        Carry out subsequent surface treatment after material has stiffened.


    • Application instructions
      • Once it has hardened, mortar must not be made workable again by adding either water or more wet mortar.

        Hairline/shrinkage cracks are safe and are not cause for complaint as they do not impair the properties of the mortar.

        Depending on the ambient conditions, in heated rooms or draughty areas, use a film or similar apparatus to prevent the material from setting too quickly.

        An additional intermediate layer of filler must be added in order to achieve the elevated surface quality grade Q3.

    • Working tools / cleaning
      • Toothed trowel / toothed blade
      • Mixer, trowel, toothed trowel, smoothing trowel, sponge float, smoothing board

      • Clean tools with water while the material is still fresh.

    • Storage / shelf life
      • Protect form moisture
      • Shelf-life 12 months
      • If stored in an unopened container and in a dry place, the product will keep for approx. 12 months.

    • Usage
      • 1.3 kg / mm thick layer / m²
      • Approx. 1.3 kg/m²/mm layer thickness, full-surface approx. 6.0 kg/m²

    • General information
      • Do not work on substrates where moisture is penetrating from the rear.

        The colour that is obtained after drying and hardening depends on the ambient conditions and the processing method. For instance, a freshly smoothed surface will be lighter than one that is smoothed later or roughened. Different grain sizes of the same product may lead to slight differences in colour. Substrates soaked from the back may cause discolouration.

        May contain traces of pyrite (iron sulphide).

        Do not use on gypsum-based substrates.

        The mixing water must be of drinking water quality.

        Low chromate content in accordance with Directive 2003/53/EC.

        Always set up a trial area/trial areas first.

        Deviations from applicable regulations must be agreed separately.

        The relevant test certificates must be observed when planning and carrying out work.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.