• Schimmel-Sanierfarbe

    Article No. 299105

    Color SL

    Silica-based, capillary-active interior wall paint. A component in the Remmers Mould Remediation System

    Colour: white | 2991
    Size / Quantity

    Discontinued product This container size is being phased out and is only available to a limited extent.

    Brochures

    product.brochures.loading

    Product specifications

    On delivery

    Density (20°C) 1.48 kg/l
    Viscosity Suitable for working
    Wet abrasion class
    (DIN EN 13300)
    3

    Once fully cured

    Once fully cured

    Colour White
    Degree of gloss Dull matt

    The stated values represent typical product characteristics and are not to be construed as binding product specifications.

    Field of application

    • For use indoors
    • Opaque coating in mould restoration systems
    • Colour design of areas adjacent to surfaces rehabilitated with a mould restoration system
    • For use on mineral renders in groups PI-PIII as well as on gypsum plasterboard, wallpaper (rough fibre) and on old, matt, load-bearing dispersion coatings

    Properties

    • Water-based
    • Inhibits mould
    • Low emissions
    • Free from film preservation and wood protection biocides
    • Free from solvents and plasticizers
    • Open to vapour diffusion sd < 0.01 m
    • Maximum particle size: fine (<100μ)
    • Hiding power class 2 at 7 m²/l
    • Wet abrasion: class 3
    • Degree of gloss: dull matt
    • Preparation
      • Substrate requirements

        Dry, clean, free of dust and cracks and capable of supporting a load.

        Structural deficiencies such as heat bridges must be eliminated.

        Condensation must be avoided.

      • Preparations

        Absorbent, mineral substrates (e.g. renders in mortar group PI-PIII) must be primed with Silicate Strengthener.

        Absorbent gypsum plasterboard must be primed with Primer Hydro F (Art. 2842).

    • Application
      • By brush / By roller / Airless/airmix spraying
      • Application temperature: min. 8 °C max. 25 °C
      • Application requirements

        Temperature of the material, air and substrate: from min. +8 °C to max. +25 °C

      • Stir well.

        Coat the surface using a suitable tool.

        Apply the material in 2 coats, depending on the condition of the substrate.

        Wait at least 8 hours between coats.

    • Application instructions
      • Take appropriate measures to protect adjacent building elements and materials that should not come into contact with the product.

        For the first coat, the material can be diluted with up to 10% water.

    • Working tools / cleaning
      • By brush / By roller / Airless/airmix spraying
      • Paintbrush, roller, wide brush, airless spraying equipment

      • Clean tools with water while the material is still fresh.

        Clean splashed material with water while the material is still fresh.

    • Storage / shelf life
      • Shelf-life 12 months
      • Store frost-free and cool / protect for moisture / close containers
      • If stored unopened in its original container in a cool, dry place and protected against frost, the product will keep for at least 12 months.

    • Usage
      • Total application/absorption rate 300 ml Total / m²
      • Approx. 0.15 l/m² per coat (depending on the condition of the substrate).

      • Apply to a large enough trial area to determine the precise amount required.

    • General information
      • The applicable regulations and legal requirements must be observed.

        Deviations from applicable regulations must be agreed separately.

        Always set up a trial area/trial areas first.

    • Disposal instructions
      • Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.

    • Safety / regulations
      • For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet.