Article No. 697511
Once fully cured
Characteristic data of the product
Discharge resistance < 10^6 ohms (system resistance according to DIN 1081, see test certificate)
The stated values represent typical product characteristics and are not to be construed as binding product specifications.
Field of application
- Electrically dissipative coating
- Can be subjected to mechanical loads
- Can be subjected to chemical loads
- Optional slip resistance (when used in a system)
- Suitable for hand pallet trucks and forklift trucks
The substrate must be firm, dimensionally stable, capable of bearing loads and free of loose constituents, dust, oil, grease, rubber marks and other substances that could interfere with adhesion.
The tensile strength of the surface of the substrate must be at least 1.5 N/mm² on average (smallest individual value of at least 1.0 N/mm²), and the compressive strength must be at least 25 N/mm².
A suitable Remmers epoxy primer or epoxy scratch coat must always be used.
Before the application of the product a smooth surface must be produced, e.g. with a scratch coat.
Refer to the current Technical Data Sheet for detailed information on the single products.
Epoxy Conductive must be applied according to the current Technical Data Sheet as transverse conducting layer.
Add the entire quantity of the hardener (component B) to the base compound (component A).
Mix thoroughly with a slow-speed electric mixer
(approx. 300 - 400 rpm).
Mix for at least 3 minutes.
Insufficient mixing is indicated by streaks forming.
Temperature of the material, air and substrate: from min. +10 °C to max. +30 °C
As a general principle, higher temperatures will reduce and lower temperatures will increase the times stated.
Working tools / cleaning
Toothed trowel, notched spreader, looped roller, spiked roller, suitable mixing equipment
More detailed information can be found in the Remmers Tool Programme.
Clean tools, equipment and splashed material immediately while fresh with V 101 Thinner.
Take suitable protective and waste disposal measures when cleaning.
Storage / shelf life
If stored unopened in the original container and kept cool, dry and protected from frost, min. 12 months (component A)/min. 24 months (component B).
See application examples
The stated approximate application quantities refer to smooth, level substrates.
Pour the material onto the prepared substrate and then distribute using a suitable tool, e.g. a notched trowel or notched scraper.
Then rework with a looped roller or spiked roller.
approx. 1.8 - 2.5 kg/m² binder
Unless otherwise specified, all of the values and application rates given above have been determined under laboratory conditions (20 °C). Slight deviations from these values may arise if the product is worked with on site.
When coating continuous surfaces, only use materials with the same batch number as slight differences in colour, gloss and texture may occur.
The conductivity of the coating is due to its carbon fibres. These are only slightly visible in highly opaque and darker colours. Colours with low opacity should not be used on account of the visibility of the carbon fibres and the potential for the black transverse conducting layer to show through.
Before the application of the covering layer, the correct functioning of the transverse conducting layer and of the connections must be proved and registered in a measurement report.
Low levels of air humidity can cause a higher discharge resistance, uneven or thicker layers can even lead the coating to not be conductive at all.
Thin layers, sloping surfaces and low temperatures may impair the visual appearance.
Abrasive mechanical loads leave traces of wear.
Exposure to vehicles with metal or polyamide tyres as well as dynamic concentrated loads can cause faster wearing of the coating.
Epoxy resins are generally not colourfast when exposed to UV light or weather.
In case of repairs on the surface or working up to existing surfaces, there will be a visible transition in appearance and texture.
Further notes on working, system construction and maintenance of the listed products can be found in the latest Technical Data Sheets and the Remmers system recommendations.
Larger quantities of leftover product should be disposed of in the original containers in accordance with the applicable regulations. Completely empty, clean containers should be recycled. Do not dispose of together with household waste. Do not allow to enter the sewage system. Do not empty into drains.
Safety / regulations
For professional users only!
For further information on the safety aspects of transporting, storing and handling the product and on disposal and environmental matters, please see the current Safety Data Sheet and the brochure entitled "Epoxy Resins in the Construction Industry and the Environment", issued by Deutsche Bauchemie e.V. (2nd edition 2009).